It is pretty hard to drive through any manufactured home community and find a home that doesn’t have some type of attached patio cover, carport, deck, Florida room or door canopy. In fact, it is so common that it is almost expected by homeowners and routinely overlooked by installers, retailers, community owners and building code officials. I think we should talk about this common practice to be certain we are doing the right thing.
A typical manufactured home installation manuals will say something like this:
Install site-built structures such as steps, landings, garages, awnings, carports, breezeways, porches, decks, railings, sheds and utility rooms to the manufacturer’s instructions and according to the following:
- Construct site-built structures to be structurally independent unless provided for in the design of the home
(there are additional bullet points in the home installation instructions that we will explore in future posts).
So why must these common awnings, landings, steps and the like, have to be “structurally independent” of the manufactured home?
It all starts with the Manufactured Home Construction & Safety Standards (HUD Code) and the Model Installation Standards. The HUD Code is no different from other building codes as they all establish the minimum building code requirements. Building codes cannot anticipate aftermarket construction or additions, and neither can the home producers. So, when we are thinking about attaching patio covers or carports to a manufactured home, we need to focus on the potential impact these added structures can have on the home and the foundation.
Unauthorized site-built additions to a home can impose unintended vertical and horizontal loads beyond what the building code minimum requires. Let‘s start with a look at the vertical load, and save the horizontal (wind) load for the next post.
Most manufactured homes are designed to handle a roof snow load of 20 to 40 pounds per square foot (psf) based on where the home is to be installed. In addition to this snow load, manufacturers must include the actual weight of the home itself (somewhere around 20-25 psf) and the assumed weight of the contents inside of the home (for furnishing, people, pets, etc.). The HUD Code requires that the manufacturers calculate this as an additional 40 psf. Ultimately, a typical manufactured home must be designed to support between 80 and 105 psf with limited deflection of the structure. The foundations are then designed to transfer all of this weight into the ground to assure a stable, plumb and level home.
Now let’s assume you attach a 20’ x 12’ (240 sq. ft.) patio cover to fascia board of the home. For a home located in the south roof load zone, that would add 4,800 lbs. (240 sq. ft x 20 psf of snow) of potential snow load beyond what was intended by the manufacturer of the home (not to mention the weight of the patio cover!). About half of that load would be transferred to the columns supporting the front of the patio cover, but the remaining weight (2,400 lbs.) is being transferred back to the fascia board, into the roof trusses and into the structure and foundation of the manufactured home itself.
You have just added over a ton of weight to the home that was not accounted for by the building code or the design of the home.
I have seen first hand where this added weight has led to ceiling cracks, inoperative windows and doors, floors bowing, and piers cracking, breaking or sinking into the ground and other structural failures.
There are some other issues to consider as well. The fascia board is not intended to resist the pull of an awning or patio cover. Fascia boards can easily pull free from the home and cause significant damage to the home. The same can be said for decks attached to the floor rim (or band) joist. You run the risk of deck collapse since the rim joist attachment to the floor joists in a manufactured home is not designed for attachment of a deck. The International Residential Code does not allow deck attachment to rim or band joists without a positive attachment such as a deck tension ties. Basically, a threaded rod and bracket that runs through the rim joist and screws to the floor joists.
See https://www.windsorlocksct.org/site/deck_lat_load.pdf for more details.
So that leaves the installer with two options:
- Install columns on both sides of an added structure so the home is not bearing any additional weight.
- Ask the home manufacturer to design the home to accept whatever loads will be added. In fact, a few manufacturers already have some designs, but typically they call for attachment to the side wall, not the fascia board.
Ok…we are just starting to explore this issue and there is much more to discuss! Let’s talk about how added structures impact horizontal (wind) loads in our next post.